Показать сокращенную информацию
dc.contributor.author | Тверской, М. М. | |
dc.contributor.author | Tverskoy, M. M. | |
dc.date.accessioned | 2013-08-16T09:12:06Z | |
dc.date.available | 2013-08-16T09:12:06Z | |
dc.date.issued | 2011 | |
dc.identifier.citation | Тверской, М. М. Алгоритм расчета операционных размеров при обработке поверхностей вращения / М. М. Тверской // Вестник ЮУрГУ. Серия Машиностроение.- 2011.- Вып. 17. № 11 (228).- С. 57-61.- Библиогр.: с. 61 (3 назв.) | ru_RU |
dc.identifier.issn | 1991-976X | |
dc.identifier.uri | http://dspace.susu.ac.ru/handle/0001.74/1995 | |
dc.description | Тверской Михаил Михайлович. Доктор технических наук, профессор, заведующий кафедрой «Автоматизация механосборочного производства», Южно-Уральский государственный университет (г. Челябинск). Область научных интересов - технология и автоматизация машиностроения. Тел.: (351)267-92-12. Mikhail M. Tverskoy. The Doctor of engineering science, the head of "Mechano-Assembley Automation" department of South Ural State University, Chelyabinsk, Russia. Professional interests: technology and automation of engineering industry. Tel.: (351) 267-92-12. | ru_RU |
dc.description.abstract | Алгоритм расчета операционных размеров при многооперационной обработке поверхности вращения основан на составлении и решении векторной размерной цепи для каждой из операций, начиная с последней. Многозвенная векторная размерная цепь приводится к трехзвенной линейной размерной цепи, замыкающим звеном которой является припуск. Составляющими звеньями этой цепи являются радиусы поверхностей, получаемых на двух смежных переходах, и результирующий эксцентриситет между этими поверхностями. Радиус поверхности, получаемой на предшествующем переходе, неизвестен и подлежит расчету. Приводится алгоритм вычисления вероятностных числовых характеристик результирующего эксцентриситета и последующего расчета операционного размера. Расчет по описанному алгоритму продолжается до определения операционного размера заготовительной операции. The algorithm of calculation of the dimensions for machining operations during multi-operational machining of surface of revolution is based on making-up and solving of vector dimensional chain for each operation starting with the last one. Multi-component vector dimensional chain is transformed to three-component linear dimensional chain, in which allowance performs as closed component. Partial components of this chain are radiuses of the surfaces, which were made during two neighboring operations, and the resulting eccentricity between these surfaces. The radius of the surface, which was made during previous operation, is unknown and has to be calculated. The algorithm of calculation of probabilistic numerical characteristics of the resulting eccentricity and the following calculation of the dimension for machining operation is shown. The calculations according to the algorithm described are going on until the dimensions for producing the metal bar are found. | ru_RU |
dc.language.iso | other | ru_RU |
dc.publisher | Издательский центр ЮУрГУ | ru_RU |
dc.relation.ispartof | Вестник ЮУрГУ. Серия Машиностроение | |
dc.relation.ispartof | Vestnik Ûžno-Ural’skogo gosudarstvennogo universiteta. Seriâ Mašinostroenie | |
dc.relation.ispartof | Bulletin of SUSU | |
dc.relation.ispartofseries | Машиностроение;Вып. 17 | |
dc.subject | операционный размер | ru_RU |
dc.subject | размерная цепь | ru_RU |
dc.subject | эксцентриситет | ru_RU |
dc.subject | припуск | ru_RU |
dc.subject | dimension for machining operation | ru_RU |
dc.subject | dimensional chain | ru_RU |
dc.subject | eccentricity | ru_RU |
dc.subject | allowance | ru_RU |
dc.subject | УДК 621.753.5 | ru_RU |
dc.title | Алгоритм расчета операционных размеров при обработке поверхностей вращения | ru_RU |
dc.title.alternative | The algorithm of calculation of the dimensions for machining operations of surface of revolution | ru_RU |
dc.type | Article | ru_RU |